Trying Flydumps Premium Cisco 642-691 PDF And VCE Braindumps For 100 Percent Passing Exam

Free Sharing Flydumps Cisco 642-691 exam questions and answers are constantly being revised and updated for relevance and accuracy.Many candidates has passed the Cisco 642-691 exam easily by training the new version.100% pass rate.

Exam A
QUESTION 1
For which purpose is the command mpls ldp maxhops used?
A. In large ATM-MPLS networks, the LFIB can become too large and it may be necessary to limit the maximum diameter of the MPLS LSPs.
B. Because downstream-on-demand label allocation uses hop count to control loop detection, it maybe necessary to limit the maximum diameter of the MPLS network.
C. Because end-to-end delay can cause problems with some voice applications, it may be necessary to limit the maximum diameter of the MPLS network.
D. When interconnecting large frame mode MPLS and cell mode networks it may be necessary to limit the maximum network diameter to prevent forwarding loops.
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 2
Refer to the diagram. What problem can be caused by the second P router summarizing the loopback address of the egress PE router?

A. The first P router will be faced with a VPN label which it does not understand.
B. The second P router will be faced with a VPN label which it does not understand.
C. The egress PE router will not be able to establish a label switch path (LSP) to the ingress PE router.
D. A label switch path (LSP) will be established from the ingress PE router to the egress PE router, an event that is not desirable.
E. The ingress PE router will not be able to receive the VPN label from the egress PE router via MP-IBGP.
Correct Answer: B Section: (none) Explanation
Explanation/Reference: QUESTION 3
In a central services topology, which routes do client VRFs contain?
A. routes from the client site, but not from the server site
B. routes from the server site, but not from the client site
C. routes from both the client site and the server site
D. only EBGP routes from either the client site or the server site
Correct Answer: C Section: (none) Explanation
QUESTION 4
On a dedicated subinterface implementation, PE-2 must establish an address-family vrf IPv4 BGP neighbor relationship with which router?

A. CE-1
B. CE-2
C. PE-1
D. PE-IG
E. CE-1 and CE-2
F. PE-1 and PE-IG
Correct Answer: B Section: (none) Explanation
Explanation/Reference: QUESTION 5
What are three drawbacks of a peer-to-peer VPN using a shared provider edge (PE) router? (Choose three.)
A. A full mesh of virtual circuits is required between the customer sites.
B. All the customers have to share a common IP address space.
C. Optimal routing between customer sites cannot be guaranteed.
D. The shared PE router has to know all routes for all customers.
E. Packet filters are required on the PE routers.
Correct Answer: BDE Section: (none) Explanation
QUESTION 6
Which two of the following statements regarding LDP are true? (Choose two.)
A. LDP can also be used between nonadjacent routers using multicast LDP hello messages.
B. LDP does not require periodic hello messages once the LDP session has been established between the LDP peers.
C. LDP hello messages use TCP packets with a destination port number of 646.
D. Multiple sessions can be established between a pair of LSRs if they use multiple label spaces.
E. Per-platform label space can be identified by a label space ID of 0 in the LDP identifier field.
Correct Answer: DE Section: (none) Explanation
Explanation/Reference:
QUESTION 7
Refer to the exhibit. Which two of the following statements about the MPLS configurations are true? (Choose two.)

A. The VPI range being configured is the default VPI range.
B. The router is missing the mpls label protocol ldp configuration command on its ATM 0/0.1 subinterface to make it an LC-ATM enabled subinterface.
C. There is a problem with the configurations because the control VC should be set to 0 32 instead.
D. The ATM switch is using VC merge since VC merge is enabled by default.
E. For MPLS label allocations, both VPI 6 and 7 can be used.
Correct Answer: DE Section: (none) Explanation
QUESTION 8
What does the following command accomplish? sanjose#clear ip bgp 10.1.1.1 in prefix-filter
A. The sanjose router will perform an outbound soft reconfig to the 10.1.1.1 neighbor.
B. The sanjose router will send out the ORF prefix-list so that a new route refresh will be received from the
1.1.1 neighbor.
C. The 10.1.1.1 router will perform an inbound soft reconfig on the updates from the sanjose neighbor.
D. The 10.1.1.1 router will send out the ORF prefix-list so that a new route refresh will be received from the sanjose neighbor.
E. The bgp session between the sanjose and the 10.1.1.1 router will be reset so that all the new bgp updates from the 10.1.1.1 router can be processed by the inbound prefix-list at the sanjose router.
F. The bgp session between the sanjose and the 10.1.1.1 router will be reset so that all the new bgp updates from the sanjose router can be processed by the inbound prefix-list at the 10.1.1.1 router.
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 9
Based on the topology diagram shown in the exhibit, when should BGP be used as the routing protocol between the customer and the ISP?

A. If physical link failures can not be detected by the link-level procedures.
B. If the customer wants to affect how the ISP will route the customer’s traffic out to the rest of the Internet.
C. If the ISP does not support static routing with the customer.
D. If the customer is using provider-assigned (PA) addresses inside the customer’s network.
E. If the customer is using private addresses inside the customer’s network.
Correct Answer: A Section: (none)
Explanation
QUESTION 10
Based on the network diagram shown in the exhibit, what is the correct configuration on the customer edge router used to conditionally announce the customer networks to the ISP?

A. router bgp 65001 ! neighbor commands not shown network 192.168.8.0 mask 255.255.252.0 ! ip route 192.168.8.0 255.255.252.0 192.168.8.33
B. router bgp 65001 ! neighbor commands not shown aggregate-address 192.168.8.0 255.255.252.0 summary-only ! ip route 192.168.8.0 255.255.252.0 192.168.8.33
C. router bgp 65001 ! neighbor commands not shown network 192.168.8.0 network 192.168.9.0 network 192.168.10.0 network 192.168.11.0 ! ip route 192.168.8.0 255.255.255.0 null0 ip route 192.168.9.0 255.255.255.0 null0 ip route 192.168.10.0 255.255.255.0 null0 ip route 192.168.11.0 255.255.255.0 null0
D. router bgp 65001 ! neighbor commands not shown aggregate-address 192.168.8.0 255.255.252.0 summary-only ! router ospf 1 network 192.168.8.0 0.0.3.255 area 0
E. router bgp 65001 ! neighbor commands not shown aggregate-address 192.168.8.0 255.255.252.0 ! ip route 192.168.8.0 255.255.252.0 null0
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 11
Which two statements about a transit AS are correct? (Choose two.)
A. A transit AS has eBGP connection(s) to only one external AS.
B. Routes between ASs are always exchanged via eBGP.
C. A transit AS uses an IGP like OSPF or ISIS to propagate the external networks within the transit AS.
D. Core routers within a transit AS normally use default routing to reach the external networks.
E. iBGP sessions can be established between non directly connected routers.
Correct Answer: BE Section: (none) Explanation
QUESTION 12
Based on the network diagram shown in the exhibit, both R5 and R6 are clients of the R2 RR. When the 0.0.0/8 iBGP update from R3 is received by the R2 RR, which router(s) will R2 reflect the update to?

A. R1 only
B. R5 and R6
C. R5, R6 and R1
D. R4, R5 and R6
E. R4, R5, R6 and R1
F. to no other router
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 13
Which show command can be used to display the originator ID and cluster-list?
A. show ip bgp
B. show ip bgp sum
C. show ip route bgp
D. show ip route {prefix}
E. show ip bgp {prefix}
F. show ip bgp neighbors {ip address}
Correct Answer: E Section: (none) Explanation
Explanation/Reference:
QUESTION 14
Which command is used to configure the external, confederation-wide AS number?
A. router(config)#router bgp {as-number}
B. router(config-router)#bgp confederation peers {as-number}
C. router(config-router)#bgp confederation identifier {as-number}
D. router(config-router)#bgp cluster-id {as-number}
E. router(config-router)#neighbor {ip address} remote-as {as-number}
Correct Answer: C Section: (none) Explanation
QUESTION 15
As the penalty for a flapping route decreases and falls below a certain limit, the route is unsuppressed. What is the name of that limit?
A. half-life limit
B. suppress limit
C. max-suppress-time limit
D. reuse limit
E. unsuppress limit
F. penalty limit
Correct Answer: D Section: (none) Explanation
Explanation/Reference: QUESTION 16
What is the difference in implementation between a managed CE services MPLS VPN and a central services MPLS VPN?
A. RD assignment
B. selective routes export
C. selective routes import
D. MP-BGP route redistribution filtering
E. CE-PE routing process
F. none
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 17
In a Transit AS, how do the internal routers within the Transit AS forward packets destined for the external networks using a scalable solution?
A. using the default route
B. using the IGP routes where the external networks are redistributed into the IGP by the edge routers
C. using the EBGP routes where the external networks are redistributed into the IBGP by the edge routers
D. using the IBGP routes, then using recursive lookup based on IGP information to resolve the BGP next-hop
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 18
Given the following configurations, R2 and R3 are not able to successfully establish the IBGP session using the loopback 0 interfaces. What could be the cause of this problem?

! output omitted
!
hostname R2 ! interface loopback 0 ip address 2.2.2.2 ! interface e0 ip address 10.1.1.1 255.255.255.0 no shut ! interface e1 ip address 10.2.2.1 255.255.255.0 no shut ! router bgp 65101 neighbor 172.16.1.1 remote-as 65100 neighbor 3.3.3.3 remote-as 65101 ! router eigrp 101 network 10.0.0.0 network 2.0.0.0 ! !
! output omitted !
hostname R3 ! interface loopback 0 ip address 3.3.3.3 ! interface e0 ip address 10.1.1.2 255.255.255.0 no shut ! interface e1 ip address 10.2.2.2 255.255.255.0 no shut ! router bgp 65101 neighbor 192.168.1.1 remote-as 65102 neighbor 2.2.2.2 remote-as 65101 ! router eigrp 101 network 10.0.0.0 network 3.0.0.0 !
A. The “No Sync” BGP configuration command is missing.
B. R2 and R3 are not using the loopback0 IP address as the source address for the BGP messages to each other.
C. The “network 2.0.0.0” BGP configuration command is missing on R2 and the “network 3.0.0.0” BGP configuration command is missing on R3.
D. The “neighbor 2.2.2.2 ibgp-multihop 2” BGP configuration command is missing on R3 and the “neighbor 3.3.3.3 ibgp-multihop 2” BGP configuration command is missing on R2.
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 19
AS-Path prepending is used in AS1 in order to influence the return traffic path from AS 5 to AS 1 through the higher speed path via AS 2. _____ needs to be configured for AS-Path prepending and a minimum of _____ of the AS number should be prepended.

A. R1; one copy
B. R2; one copy
C. R1; two copies
D. R2; two copies
E. R2; three copies
Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 20
In a multihomed environment with two ISP connections, which two statements are true? (Choose two.)
A. The customer should not be configured to act as a transit AS between the two ISPs.
B. It is recommended that the multi-homed customer use a registered (public) AS number.
C. AS-Path prepending can be configured on the customer’s edge router to influence the BGP path selection process for the outbound traffic (traffic from the customer to the ISPs).
D. The customer can use Local Preference on the customer’s edge routers to influence the BGP path selection process for the inbound traffic (traffic from the ISPs to the customer).
E. The advertisement of the customer’s IP address space can be conditioned by the customer’s edge routers by using a static route to the null0 interface and by using the proper network statement under router bgp.
Correct Answer: AB Section: (none) Explanation
Explanation/Reference:
QUESTION 21
Which two configuration commands will complete the BGP configuration on R1 so it will conditionally announce the 172.0.0.0/8 prefix to R4 via BGP? (Choose two.)

1.
___________________________

! router bgp 65001 neighbor 172.16.1.1 remote-as 65001 neighbor 2.2.2.2 remote-as 65001 neighbor 4.4.4.4 remote-as 387 !

2.
____________________________
A. 2. network 172.16.0.0 auto-summary
B. 2. network 172.0.0.0 mask 255.0.0.0
C. 1. ip route 172.0.0.0 255.0.0.0 null0
D. 1. ip route 172.0.0.0 255.0.0.0 null0 255
E. 1. ip route 172.0.0.0 255.0.0.0 172.16.1.1
F. 2. aggregate-address 172.0.0.0 mask 255.0.0.0
Correct Answer: BE Section: (none) Explanation
Explanation/Reference:
QUESTION 22
Which four attributes are used by BGP to detect routing loops? (Choose four.)
A. AS-Path
B. Cluster ID
C. Cluster List
D. Originator ID
E. Community ID
Correct Answer: ABCD Section: (none) Explanation
QUESTION 23
Which three statements are true about route reflectors? (Choose three.)
A. If the route is learned from an EBGP peer by the route reflector, it is reflected to all IBGP and EBGP peers.
B. If the route is learned from a non-client IBGP peer by the route reflector, it is reflected to all EBGP peers only.
C. If the route is learned from a non-client IBGP peer by the route reflector, it is reflected to EBGP peers and clients only.
D. If the route is learned from a client IBGP peer by the route reflector, it is reflected to all clients only, except the originating client.
E. If the route is learned from a client IBGP peer by the route reflector, it is reflected to all EBGP peers, non-clients, and clients (except the originating client).

Correct Answer: ACE Section: (none) Explanation
Explanation/Reference:
QUESTION 24
Based on the following show ip bgp neighbors 2.2.2.2 output, which two statements are true? (Choose two.)
R1#show ip bgp neighbors 2.2.2.2 BGP neighbor is 2.2.2.2, remote AS 102, internal link Index 1, Offset 0, Mask 0x2 BGP version 4, remote router ID 66.0.0.1 BGP state=Established, table version=1, up for 00:14:52 Last read 00:00:52, hold time is 180, keepalive interval is 60 seconds Minimum time between advertisement runs is 5 seconds Received 233 messages, 0 notifications, 0 in queue Sent 206 messages, 0 notifications, 0 in queue Prefix advertised 0, suppressed 0, withdrawn 0 Connections established 17; dropped 16 Last reset 00:15:02, due to User reset 18 accepted prefixes consume 576 bytes, maximum limit 20 Threshold for warning message 80% 0 history paths consume 0 bytes
A. R1 has accepted 20 prefixes from the 2.2.2.2 IBGP neighbor.
B. R1 generated a warning message to the router’s console after the 2.2.2.2 IBGP neighbor sent 16 prefixes to R1.
C. R1 generated a warning message to the router’s console after the 2.2.2.2 IBGP neighbor sent 15 prefixes to R1.
D. R1 will drop its neighbor relationship to the 2.2.2.2 IBGP neighbor if 2.2.2.2 sends two more additional prefixes to R1.
E. R1 will drop its neighbor relationship to the 2.2.2.2 IBGP neighbor if 2.2.2.2 sends three more additional prefixes to R1.
Correct Answer: BE Section: (none) Explanation
Explanation/Reference:
QUESTION 25
R2 is configured to prepend AS number 65102 in updates to R3. Which statement is true?

A. The BGP updates from R2 to R3 will be rejected by R3 due to loop prevention.
B. The EBGP session between R2 and R3 will be dropped due to an AS-Path prepend configuration error.
C. The AS-Path length via AS 65102 will increase to influence the return traffic path selected by the remote ASs.
D. The AS-Path length via AS 65102 will decrease to influence the return traffic path selected by the remote ASs.
E. The AS-Path prepend configuration command using the remote AS number (65102) will be rejected by IOS at R2.

Correct Answer: A Section: (none) Explanation
QUESTION 26
During the autonomous system number migration process, which BGP feature allows a BGP router to act as a router within one autonomous system to some BGP neighbors but also appear to be in another autonomous system to other neighbors?
A. remove-private-as
B. local-as
C. as-path prepending
D. AS override
E. Site-of-Origin (S00)
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 27
Based on this configuration, which two peering router neighbor statements are correct? (Choose two.)
router bgp 50001 neighbor 192.168.1.1 remote-as 50001 neighbor 10.1.1.1 remote-as 50002 neighbor 10.1.1.1 local-as 50003 ! output omitted
A. EBGP – neighbor 10.1.1.2 remote-as 50003
B. EBGP – neighbor 10.1.1.2 remote-as 50001
C. EBGP – neighbor 10.1.1.2 remote-as 50001 and neighbor 10.1.1.2 local-as 50003
D. IBGP – neighbor 192.168.1.2 remote-as 50001
E. IBGP – neighbor 192.168.1.2 remote-as 50003
F. IBGP – neighbor 192.168.1.2 remote-as 50003 and neighbor 192.168.1.2 local-as 50001
Correct Answer: AD Section: (none) Explanation
Explanation/Reference:
QUESTION 28
Which configuration task requires configuring the bgp cluster-id {cluster-id} command?
A. configuring the member ASs within a BGP confederation
B. configuring the BGP confederation ID
C. configuring hierarchical BGP confederations
D. configuring redundant BGP confederations
E. configuring hierarchical route reflectors
F. configuring redundant route reflectors
Correct Answer: F Section: (none) Explanation
Explanation/Reference:
QUESTION 29
Refer to the diagram. What should be changed within AS 50001 to improve the route reflector design?

A. Add a physical link between R1 and R2.
B. Add a physical link between the clients (R3 and R4, and between R4 and R5).
C. Remove the IBGP session between the two redundant RRs (R1 and R2).
D. Add an IBGP session between each pair of clients (between R3 and R4, R4 and R5).
E. Make R4 the RR and R1 and R2 its clients. R3 and R5 should be a non-RR/non-client.

Correct Answer: A Section: (none) Explanation
QUESTION 30
Which command is used to advertise a summary route while suppressing only a subset of the more specific routes?
A. network {ip prefix} {mask}
B. network {ip prefix} {mask} unsuppress-map {route-map-name}
C. aggregate-address {ip prefix} {mask}
D. aggregate-address {ip prefix} {mask} summary-only
E. aggregate-address {ip prefix} {mask} suppress-map {route-map-name}
F. aggregate-address {ip prefix} {mask} as-set summary-only
Correct Answer: E Section: (none) Explanation
Explanation/Reference:
QUESTION 31
Based on the R1 router BGP configuration shown, which three statements are correct? (Choose three.)

A. R1 is in AS 50101 according to the 192.168.100.1 neighbor.
B. R1 is in AS 50101 according to the 10.1.1.1 neighbor.
C. The 192.168.100.1 neighbor must be directly connected to R1.
D. R1 is a route-reflector client.
E. The 10.4.4.4 neighbor is an EBGP neighbor.
F. BGP updates coming in from the 192.168.100.1 neighbor must be processed by the setlp route-map.

Correct Answer: ACF Section: (none) Explanation
Explanation/Reference:
QUESTION 32
What is the correct command to set the BGP scanner interval to two minutes?
A. bgp scan-time 2
B. bgp scan-time 120
C. bgp scan-time 2 60
D. The maximum scanning interval cannot exceed one minute
Correct Answer: D Section: (none) Explanation
QUESTION 33
Given the AS-path of (51002 51003) 51001 i from the show ip bgp output, what is the origin?
A. AS 51001
B. AS 51002
C. AS 51003
D. (51002 51003)
E. IGP
F. IBGP
Correct Answer: E Section: (none) Explanation
QUESTION 34
What benefit does AToM provide to the service provider’s customers?
A. By supporting Layer 2 VPNs, customers maintain control of their site-to-site routings over the WAN.
B. By supporting Layer 3 VPNs, a full mesh of virtual circuits will not be required between the different customer sites to enable optimal routing.
C. By supporting secured Layer 3 VPNs, customers do not have to deal with the complexity of configuring IPSec.
D. By supporting MPLS traffic engineering over ATM, customers can better utilize their WAN link.
E. By supporting Diff-Serv QoS, AToM allows customers to deploy voice/video applications across the WAN.

Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 35
What is a benefit of CEF switching?
A. CEF supports IP source prefix-based switching using the FIB.
B. CEF uses less memory than fast switching uses.
C. CEF is less CPU intensive than fast switching is.
D. CEF provides Netflow statistics with minimum CPU overhead.
E. CEF allows multiple data planes to share a common control plane.

Correct Answer: C Section: (none) Explanation
QUESTION 36
What are two concerns when implementing CEF switching? (Choose two.)
A. increased CPU utilization from maintaining the FIB table
B. increased memory requirement
C. the requirement to disable other IOS features such as NBAR and MQC
D. increased memory requirement on the VIP when implementing DCEF
E. configuration complexity
F. troubleshooting complexity because of the many tables that CEF maintains

Correct Answer: BD Section: (none) Explanation
QUESTION 37
With MPLS VPN-aware NAT, what additional information is tracked inside the NAT translation table?
A. RD information
B. RT information
C. VRF information
D. Multi-protocol BGP prefixes
E. MPLS Labels

Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 38
What is the purpose of the global configuration command, ip dhcp relay information option vpn?
A. enables the DHCP relay agent to insert the VPN suboptions to the BOOTP request
B. enables the DHCP relay agent to convert the broadcast DHCP request to a unicast DHCP request to a shared DHCP server
C. enables the DHCP relay agent to perform VRF-aware NAT before forwarding the DHCP request to a shared DHCP server
D. enables ODAP (On-Demand Address Pool) on the DHCP relay agent

Correct Answer: A Section: (none) Explanation QUESTION 39
Which of the following could be called a VPN identifier in the MPLS/VPN architecture?
A. route target
B. route distinguisher
C. VRF
D. VPN IPv4 address
E. BGP site-of-origin (SOO) extended community attribute

Correct Answer: A Section: (none) Explanation
QUESTION 40
An OSPF LSA type 1 route is redistributed into MP-BGP. That same route is then redistributed back from MP-BGP into OSPF on another PE router. In this case, which LSA type on the destination CE router will the OSPF route appear as?
A. LSA type 1
B. LSA type 2
C. LSA type 3
D. LSA type 4
E. LSA type 5
F. LSA type 7

Correct Answer: C Section: (none) Explanation
Explanation/Reference: Exam B
QUESTION 1
What best describes the following configuration example of allowas-in?
router bgp 100 address-family ipv4 vrf CustomerA neighbor 195.12.4.5 remote-as 123 neighbor 195.12.4.5 activate neighbor 195.12.4.5 allowas-in 2
A. permits incoming BGP updates defined by access-list 2
B. permits incoming BGP updates defined by class-map 2
C. permit incoming BGP updates defined by route-map 2
D. permits incoming BGP updates with no more than two occurrences of AS 100 in the AS path
E. permits incoming BGP updates with no more than two occurrences of AS 123 in the AS path
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 2
Using MPLS unicast IP forwarding, what will happen if an LSR receives an unlabeled incoming packet?
A. It will process switch the packet by doing a routing table lookup.
B. It will forward the packet using the LFIB.
C. It will forward the packet using the LIB.
D. It will forward the packet using the FIB.
E. It will drop the packet immediately.
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 3
When using MPLS unicast IP forwarding, what will happen if an LSR receives an incoming labeled packet but the LSR can’t find that incoming label in its LFIB?
A. The packet will be forwarded using the FIB.
B. The packet will be forwarded using the LIB.
C. The packet will be process switched by performing a route lookup in the routing table.
D. The packet will be forwarded using the LFIB with an imp-null outgoing label.
E. The packet will be dropped even if the IP destination exists in the FIB.
Correct Answer: E Section: (none) Explanation
Explanation/Reference:
QUESTION 4
When routes between MP-BGP and RIP are being redistributed, what does the option metric transparent do?
A. copies the BGP MED into the RIP hop count
B. copies the BGP local preference into the RIP hop count
C. copies the RIP hop count into the BGP local preference
D. copies the RIP hop count into the BGP MED
E. uses the default seed metric when redistributing from MP-BGP into RIP
F. uses the default seed metric when redistributing from RIP into MP-BGP

Correct Answer: A Section: (none) Explanation
QUESTION 5
Refer to the partial topology diagram shown.Service Provider 1 (SP1) assigned the customer an AS number of 65275. Service Provider 2 (SP2) assigned an AS number of 65745 to the customer. The customer decides to use AS 65275 internally. Which of the following is the correct partial router configuration to cause updates from CR1 to SP1 to report a source AS of 65275, while updates from CR2 to SP2 report the source AS of 65745 in addition to AS 65275?

A. !CR1 router bgp 65275 neighbor 1.1.1.1 remote-as 65274 neighbor 10.1.1.2 remote-as 65275 !CR2 router bgp 65275 neighbor 2.2.2.2 remote-as 65732
neighbor 2.2.2.2 local-as 65745
neighbor 10.1.1.1 remote-as 65275

B. !CR1 router bgp 65275 neighbor 1.1.1.1 remote-as 65274 neighbor 10.1.1.2 remote-as 65275 !CR2 router bgp 65745 neighbor 2.2.2.2 remote-as 65732 neighbor 2.2.2.2 local-as 65745 neighbor 10.1.1.1 remote-as 65275
C. !CR1 router bgp 65275 neighbor 1.1.1.1 remote-as 65274 neighbor 1.1.1.1 local-as 65745 neighbor 10.1.1.2 remote-as 65275 !CR2 router bgp 65275 neighbor 2.2.2.2 remote-as 65732 neighbor 2.2.2.2 local-as 65745 neighbor 10.1.1.1 remote-as 65275
D. !CR1 router bgp 65275 neighbor 1.1.1.1 remote-as 65274 neighbor 10.1.1.2 remote-as 65275 !CR2 router bgp 65745 neighbor 2.2.2.2 remote-as 65732 neighbor 2.2.2.2 local-as 65275 neighbor 10.1.1.1 remote-as 65275
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 6
In the diagram, the customer is using static routing to connect to the ISP. Which configuration on the ISP edge routers will enable load balancing and backup of the traffic to the customer?

A. ! R1 ip route 10.1.1.0 255.255.255.128 serial 0 ! R2 ip route 10.1.1.128 255.255.255.128 serial 0
B. ! R1 ip route 10.1.1.0 255.255.255.0 serial 0 ! R2 ip route 10.1.1.128 255.255.255.0 serial 0
C. ! R1 ip route 10.1.1.0 255.255.255.128 serial 0 ip route 10.1.1.128 255.255.255.128 serial 0 ! R2 ip route 10.1.1.128 255.255.255.128 serial 0 ip route 10.1.1.0 255.255.255.128 serial 0
D. ! R1 ip route 10.1.1.0 255.255.255.128 serial 0 ip route 10.1.1.0 255.255.255.0 serial 0 ! R2 ip route 10.1.1.128 255.255.255.128 serial 0 ip route 10.1.1.0 255.255.255.0 serial 0
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 7
Who should use private AS numbers?
A. multihomed customers who configured their AS as a transit AS
B. customers multihomed to two different ISPs
C. customers multihomed to a single ISP using multiple permanent links
D. customers connected to a single ISP using a single permanent link

Correct Answer: C Section: (none) Explanation
QUESTION 8
When using the redistribute ospf {process-id} command, which types of OSPF routes will be redistributed into BGP?
A. all internal (interarea and intra-area) OSPF routes
B. all external OSPF routes
C. all external OSPF routes except type 7 LSAs
D. both internal and external OSPF routes
E. only classful OSPF routes without the subnet option
F. only external OSPF routes without the match option
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 9
In the diagram, the customer is using BGP to connect to a single ISP over two permanent links. In this scenario, which input and output prefix-list filtering is typically enabled on the ISP routers? (Choose two.)

A. ip prefix-list test-in permit 10.1.1.0/24 le 32
B. ip prefix-list test-in permit 10.0.0.0/8 le 32
C. ip prefix-list test-in permit 0.0.0.0/0
D. ip prefix-list test-out permit 10.1.1.0/24 le 32
E. ip prefix-list test-out permit 10.0.0.0/8 le 32
F. ip prefix-list test-out permit 0.0.0.0/0
Correct Answer: AF Section: (none) Explanation
Explanation/Reference:
QUESTION 10
Refer to the exhibit and the following connectivity requirements. How many different VRFs are required?

Sites CE1A, CE1B, CE1C, and CE1D require connectivity among them.
Sites CE2A and CE2B require connectivity between them.
Site CE12A requires connectivity to sites CE1A, CE1B, CE1C, CE1D, and CE12B.
Site CE12B requires connectivity to sites CE2A, CE2B, and CE12A.

A. 2 VRFs
B. 3 VRFs
C. 4 VRFs
D. 6 VRFs
E. 8 VRFs
F. 10 VRFs

Correct Answer: C Section: (none) Explanation
Explanation/Reference:
QUESTION 11
Which configuration will enable the R1 router in the AS51003 sub-AS (member-AS) as a route reflector with neighbors 10.1.1.1 and 10.2.2.2 as its route-reflector clients?
A. ! R1 router bgp 51003 bgp confederation identifier 55111 bgp confederation peers 51001 51002 neighbor 10.1.1.1 remote-as 51003 neighbor 10.2.2.2 remote-as 51003
neighbor 10.1.1.1 route-reflector-client
neighbor 10.2.2.2 route-reflector-client
B. ! R1 router bgp 51003 bgp confederation identifier 55111 bgp confederation peers 51001 51002 neighbor 10.1.1.1 remote-as 51001 neighbor 10.2.2.2 remote-as 51002 neighbor 10.1.1.1 route-reflector-client neighbor 10.2.2.2 route-reflector-client
C. ! R1 router bgp 55111 bgp confederation identifier 51003 neighbor 10.1.1.1 remote-as 51003 neighbor 10.2.2.2 remote-as 51003 neighbor 10.1.1.1 route-reflector-client neighbor 10.2.2.2 route-reflector-client
D. ! R1 router bgp 55111 bgp confederation identifier 51003 neighbor 10.1.1.1 remote-as 55111 neighbor 10.2.2.2 remote-as 55111 neighbor 10.1.1.1 route-reflector-client neighbor 10.2.2.2 route-reflector-client
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 12
When configuring Internet access from a MPLS VPN using a separate subinterface, which two configurations are required on the PE router? (Choose two.)
A. Use the ip vrf forwarding command on the subinterface that is used for MPLS VPN access.
B. Use the ip vrf forwarding command on the subinterface that is used for Internet access.
C. The CE router is configured as a BGP neighbor in both the global BGP process and inside the VPN in the VRF.
D. The PE-to-CE VPN and Internet routing are configured using two separate address-family ipv4 vrf commands, one for VPN routing and one for Internet routing.
Correct Answer: AC Section: (none) Explanation
Explanation/Reference:
QUESTION 13
Refer to the exhibit and the following connectivity requirements. Which type of MPLS VPN is being implemented?

Sites CE1A and CE1B require connectivity to each other.
Sites CE2A and CE2B require connectivity to each other.
Site CE1C requires connectivity to sites CE1A, CE1B, CE3A, and CE3B.
Site CE2C requires connectivity to sites CE2A, CE2B, CE3A, and CE3B.
Sites CE3A and CE3B require connectivity to each other and to CE1C and CE2C.

A. central services MPLS VPN
B. overlapping MPLS VPN
C. simple VPN
D. combinations of overlapping and central services MPLS VPN
E. combinations of simple and central services MPLS VPN
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 14
When configuring Internet access using a separate MPLS VPN, which three statements are correct? (Choose three.)
A. The Internet backbone is separate from the MPLS VPN backbone.
B. Two dedicated physical or logical links between the PE and the CE routers are required.
C. An Internet gateway is connected as a CE router to the MPLS VPN backbone.
D. An Internet gateway shall insert full Internet routing into the Internet VPN to achieve optimal routing.
E. The customer’s Internet access is enabled by combining the Internet VPN with the Customer VPN using overlapping VPN topology.
Correct Answer: ACE Section: (none) Explanation
Explanation/Reference:
QUESTION 15
Refer to the exhibit. Based on the show outputs, which condition could be preventing the P1 router from establishing TDP adjacency with its neighbor over the s0/0.211 and s0/0.212 subinterfaces?

A. The s0/0.211 and s0/0.212 subinterfaces line protocol are in the down state.
B. The P1 router cannot establish a TCP session with its neighbors.
C. The P1 router is missing the mpls label protocol LDP command.
D. The show mpls tdp neighbor command needs to be used to view the TDP neighbor status.
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 16
BGP is used as the CE-PE routing protocol in an MPLS VPN. The customer routes are successfully propagated from the CE router to the ingress PE router, but they are not showing up on the egress PE router. What is the most likely cause of the problem?
A. There is a BGP-to-MPBGP redistribution error on the ingress PE router.
B. There is a MPBGP-to-BGP redistribution error on the egress PE router.
C. One of the P routers is performing route summarization, breaking the path between the ingress and the egress PE routers into two LSPs.
D. RTs attached to the CE routes exported by the ingress router are not matched by at least one of the import RTs on the egress PE router.
E. A route reflector is used to propagate the routes from the ingress PE router to the egress PE router, thus breaking the LSP
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 17
The MPLS VPN provider is using a separate Internet VPN to provide Internet access to its MPLS VPN
customers. Currently, all of its customers are not able to access the Internet. The partial provider’s CE-Internet
router configuration is shown below. Based on the configuration, what could be the cause of the problem?
ip route 0.0.0.0 0.0.0.0 10.1.1.1
!
router bgp 51001 network 0.0.0.0 neighbor 10.2.2.2 remote-as 51002 ! PE neighbor router neighbor 10.2.2.2 prefix-list test1 out neighbor 10.3.3.3 remote-as 51001 ! Another Internet router neighbor 10.3.3.3 prefix-list test2 out ! ip prefix-list test2 permit 0.0.0.0/0 ip prefix-list test1 permit 0.0.0.0/0 ge 1
A. The test2 prefix-list should be applied to the 10.2.2.2 neighbor and the test1 prefix-list should be applied to the 10.3.3.3 neighbor.
B. Both prefix-lists should be applied in the “in” direction instead of the “out” direction.
C. The network command is missing the mask 0.0.0.0 option.
D. The network command is missing the mask 255.255.255.255 option.
E. The neighbor 10.2.2.2 activate and the neighbor 10.3.3.3 activate commands are missing.
Correct Answer: A Section: (none) Explanation
Explanation/Reference:
QUESTION 18
Refer to the outputs shown in the exhibit. What could be preventing the R1 router from receiving any prefixes from the R2 BGP neighbor?

A. There is a TCP session establishment problem between R1 and R2.
B. The no sync command is missing on R2.
C. The no sync command is missing on R1.
D. R2 is using the wrong AS number in its neighbor 192.168.31.2 remote-as statement.
E. R1 is using the wrong AS number in its neighbor 192.168.31.1 remote-as statement.
F. Both R1 and R2 are not using a loopback address to source their BGP packets.
Correct Answer: E Section: (none) Explanation
Explanation/Reference:
QUESTION 19
Refer to the configuration shown. What could cause the BGP prefixes from the 10.1.1.1 BGP peer to be absent from the routing table?

A. intraconfederation EBGP configurations error
B. autosummarization
C. ebgp-multihop issue
D. BGP synchronization
E. EBGP configurations error
Correct Answer: D Section: (none) Explanation
Explanation/Reference:
QUESTION 20
The core routers within a transit AS are running both IBGP and IGP. The edge routers within the transit AS are using the next-hop-self option to establish the IBGP sessions. What can be implemented to improve the routing performance to all external prefixes?
A. enable route redistribution from BGP into IGP
B. disable BGP synchronization on all the core routers
C. enable CEF on all the core and edge routers
D. enable route redistribution from IGP into BGP
E. use route reflectors within the core
Correct Answer: C Section: (none) Explanation
Explanation/Reference: QUESTION 21

he MPLS network.
D. When interconnecting large frame mode MPLS and cell mode networks it may be necessary to limit the maximum network diameter to prevent forwarding loops.
Correct Answer: B Section: (none) Explanation
Explanation/Reference:
QUESTION 2
Refer to the diagram. What problem can be caused by the second P router summarizing the loopback address of the egress PE router?

1.
___________________________

! router bgp 65001 neighbor 172.16.1.1 remote-as 65001 neighbor 2.2.2.2 remote-as 65001 neighbor 4.4.4.4 remote-as 387 !

A. 2 VRFs
B. 3 VRFs
C. 4 VRFs
D. 6 VRFs
E. 8 VRFs
F. 10 VRFs

CCNA Cisco 642-691 contains a powerful new testing engine that allows you to focus on individual topic areas or take complete, timed exams from CCNA Cisco 642-691.The assessment engine also tracks your performance and presents feedback on a module-by-module basis, providing question-by-question CCNA Cisco 642-691 to the text and laying out a complete study plan for review.CCNA Cisco 642-691 also includes a wealth of hands-on practice exercises and a copy of the CCNA Cisco 642-691 network simulation software that allows you to practice your CCNA Cisco 642-691 hands-on skills in a virtual lab environment.The CCNA Cisco 642-691 supporting website keeps you fully informed of any exam change